Differences

This shows you the differences between two versions of the page.

--- paymentech_pinpads [2007/10/04 12:30 (17 years ago)] – created craig
+++ paymentech_pinpads [2020/10/26 17:01 (4 years ago)] – [verifone Vx820 Contactless] craig
@@ Line 1: / Line 1: @@
-====== Supported Paymentech Canada PINPads ======
+====== Supported Paymentech™ Canada PINPads ======
-===== verifone SC550 =====
-This pinpad is available from Paymentech Canada
+===== verifone Vx820 Contactless=====
+  * This device is now available the Chase Paymentech.
+  * EMV Contact and Contactless supported for the following card brands
+     * Visa
+     * Mastercard
+     * Amex
+     * Interac
+     * JCB
+  * Requires
+     * Vx820 XPI 12.08.16
+     * Netepay 5.06.10
+     * DSIEMVClientX® 1.27
+     * SystemFive version 6.2.2.262 or higher to support manual entry with CVV
+<note warning>The Canadian VX810 pinpads are **RS-232 Serial only**. You need a 9 PIN RS-232 Serial port on the back of your computer. **USB-Serial converters DO NOT WORK. I repeat, they DO NOT WORK**. They are also expensive for ones that may work. If you do not have a serial card, you can have one installed. The Edge USB-Serial converter is the only known one that works, but please don't waist your money and time on it when a serial port card can be installed for a third of the cost.
+----
+**VX820 pinpads running XPI 12.xx** can use USB if you have the VX820/Vx805 USB cable (not a usb/serial converter). Chase usually ships them configured for Serial (even if you ordered USB).
+__Instructions for changing the vx820 pinpad to use USB__
+  - At the idle prompt (Welcome screen) press both the “7” and Enter/green keys simultaneously. The terminal manager entry screen should now be displayed.
+  - Enter the password (not given here) and press the Enter/green key.
+  - Press the “2” key to select “Edit Parameters”.
+  - Press the Enter/green key to select “Group ID 1” which should be displayed.
+  - Enter the password (not given here) and press the Enter/green key.
+  - Press the Enter/green key to select “CONFIG.SYS” which should be displayed.
+  - Use the up and down arrow on the bottom left hand side of the touchscreen to scroll through the list of parameters until you find a parameter named “SACOM”.
+  - If using a USB interface cable the value should be “USB”.
+  - If using a serial interface cable the value should be “COM1” .
+  - If the value does not match the installed cabling press the “3” key to select it for editing then use the Correct/yellow key to delete the value and type the correct one as listed above the press the Enter/green key.
+  - Repeat steps 7 and 8 to ensure the “SABAUD” parameter exists and is set to “9600”.
+  - Press the Cancel/red key to return to the terminal manager screen then press 1 to restart the VX820.
+</note>
+===== verifone Vx810 =====
+  * Supports EMV Chip and PIN
+  * Not suitable for large volumnes mail order / ecommerce, use the legacy version below.
+  * Requires System Five version 6.0.70.14
+{{faq:payment_processing_setup:vx810.jpg|}}
+<note important>This version will no longer support manual entries of card numbers as Chase now requires the CVV number</note>
+===== Other information =====
+  * [[pinpads|Supported USA PINPads]]
+  * [[global_pinpads|Supported Canadian Mercury PINPads]]
+  * [[moneris_pinpads|Supported Canadian Moneris PINPads]]
+  * [[paymentech_pinpads|Supported Canadian Paymentech PINPads]]
+  * [[faq:global_canada_semi_integrated|Supported Global Payment Terminals]]