User Tools

Site Tools


paymentech_pinpads

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
paymentech_pinpads [2020/10/26 17:01 (3 years ago)] – [verifone Vx820 Contactless] craigpaymentech_pinpads [2021/08/30 16:12 (3 years ago)] (current) plagrada
Line 1: Line 1:
 ====== Supported Paymentech™ Canada PINPads ====== ====== Supported Paymentech™ Canada PINPads ======
- +https://newaccount1608055419986.freshdesk.com/a/solutions/articles/66000494394
- +
-===== verifone Vx820 Contactless===== +
-  * This device is now available the Chase Paymentech. +
-  * EMV Contact and Contactless supported for the following card brands +
-     * Visa +
-     * Mastercard +
-     * Amex +
-     * Interac +
-     * JCB +
-  * Requires  +
-     * Vx820 XPI 12.08.16 +
-     * Netepay 5.06.10 +
-     * DSIEMVClientX® 1.27 +
-     * SystemFive version 6.2.2.262 or higher to support manual entry with CVV  +
- +
-<note warning>The Canadian VX810 pinpads are **RS-232 Serial only**. You need a 9 PIN RS-232 Serial port on the back of your computer. **USB-Serial converters DO NOT WORK. I repeat, they DO NOT WORK**. They are also expensive for ones that may work. If you do not have a serial card, you can have one installed. The Edge USB-Serial converter is the only known one that works, but please don't waist your money and time on it when a serial port card can be installed for a third of the cost. +
- +
----- +
- +
- +
-**VX820 pinpads running XPI 12.xx** can use USB if you have the VX820/Vx805 USB cable (not a usb/serial converter)Chase usually ships them configured for Serial (even if you ordered USB). +
-__Instructions for changing the vx820 pinpad to use USB__ +
-  - At the idle prompt (Welcome screen) press both the “7” and Enter/green keys simultaneously. The terminal manager entry screen should now be displayed. +
-  - Enter the password (not given here) and press the Enter/green key. +
-  - Press the “2” key to select “Edit Parameters”. +
-  - Press the Enter/green key to select “Group ID 1” which should be displayed. +
-  - Enter the password (not given here) and press the Enter/green key. +
-  - Press the Enter/green key to select “CONFIG.SYS” which should be displayed. +
-  - Use the up and down arrow on the bottom left hand side of the touchscreen to scroll through the list of parameters until you find parameter named “SACOM”. +
-  - If using a USB interface cable the value should be “USB”. +
-  - If using a serial interface cable the value should be “COM1” . +
-  - If the value does not match the installed cabling press the “3” key to select it for editing then use the Correct/yellow key to delete the value and type the correct one as listed above the press the Enter/green key. +
-  - Repeat steps 7 and 8 to ensure the “SABAUD” parameter exists and is set to “9600”. +
-  - Press the Cancel/red key to return to the terminal manager screen then press 1 to restart the VX820. +
- +
-</note> +
- +
- +
-===== verifone Vx810 ===== +
-  * Supports EMV Chip and PIN +
-  * Not suitable for large volumnes mail order / ecommerce, use the legacy version below. +
-  * Requires System Five version 6.0.70.14 +
- +
-{{faq:payment_processing_setup:vx810.jpg|}} +
- +
-<note important>This version will no longer support manual entries of card numbers as Chase now requires the CVV number</note> +
- +
- +
- +
  
 ===== Other information ===== ===== Other information =====
paymentech_pinpads.1603756910.txt.gz · Last modified: 2020/10/26 17:01 (3 years ago) by craig