Differences

This shows you the differences between two versions of the page.

--- wasp_wws750_barcode_scanner [2021/01/28 12:16 (3 years ago)] – swind
+++ wasp_wws750_barcode_scanner [2021/01/28 12:48 (3 years ago)] – swind
@@ Line 5: / Line 5: @@
 {{ :barcodescan:barcodescan:wasp_wws_750:wasp_wws_750.jpg?400 |}}
-====== Overview ======
+====== Overview From Wasp's web page ======
+ - Scans Popular 1D and 2D Barcodes
+ - Data Collect 295ft (90m) from Base
+ - 30,000+ Continuous Scans on One Full Charge
+ - Durable 6.6ft (2m) Drop Spec and IP65 Rating
+ - Green Spot Technology for Good-Read Feedback
 ====== Details ======
-{{ :barcodescan:barcodescan:wasp_wws_750:wasp-wdi7500-wws750-prg.pdf |}}
+The full programming manual can be downloaded from this link \\
+{{ :barcodescan:barcodescan:wasp_wws_750:wasp-wdi7500-wws750-prg.pdf |}} \\
+Or directly from Wasp's web site. \\
+http://dl.waspbarcode.com/kb/scanner/Wasp-WDI7500-WWS750-PRG.pdf \\
 ====== Solution ======
-Good Read: When to Indicate Page 68 \\
+There are a couple options that can be enabled if the scanner appears to be dropping barcodes. From what I have seen, this occurs when the barcode scanner or the cradle loses communication with one-another. \\
-Specifies when the reader will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. \\
-Default is Indicate Good Read = After Decode \\
+Good Read: When to Indicate - Page 68 \\
-Change to Indicate Good Read = After Transmit \\
+Specifies when the reader will provide an indication (beep and/or flash its green LED), upon successfully reading a barcode. \\
+the default setting is "Indicate Good Read = After Decode". This means that the handheld will beep when it scans a valid barcode. This will work in most instances. \\
+If you are experiencing disconnects between the scanner and the cradle, you can change that setting to "Indicate Good Read = After Transmit". This means it will wait to beep until after the scanner has sent the barcode to the cradle. \\
 {{ :barcodescan:barcodescan:wasp_wws_750:page68.jpg?350 |}}
-Batch Mode Page 208 \\
+Batch Mode - Page 208 \\
-This option specifies whether to store labels in the handheld while disconnected from the base. \\
+This option specifies whether or not to store labels in the handheld while disconnected from the cradle. \\
-Options are as follows: \\
+By default batch mode is Disabled. this means the handheld will not store/batch labels. It will send the barcodes one at a time. If communication is lost between the scanner and cradle, the barcode will be lost. \\
-Default is Disabled - The handheld will not store/batch labels. \\
+ \\
-Change to Automatic - The handheld will store labels to RAM when the handheld goes out of range and is disconnected from the remote device. \\
+A better option would be to change this setting to Automatic. By doing this the scanner will store the barcodes within itself when it goes out of range and is disconnected from the cradle. \\
-Jude will change this and test. This would also help eliminate missed scans \\
+This would also help eliminate missed scans \\
 {{ :barcodescan:barcodescan:wasp_wws_750:page208.jpg?250 |}}
-Bluetooth Reconnect Attempt Mode Page 224 \\
+Bluetooth Reconnect Attempt Mode - Page 224 \\
-Enable/Disable reconnection by trigger pull. Already enabled. \\
+Enable/Disable reconnection by trigger pull. \\
+This is already enabled by default, but I am listing it here because it works with the batch mode setting above. \\
+With this enabled, if a barcode is stored in the barcode scanner but it couldn't communicate with the cradle, the next time you pull the trigger, it will re-attempt to send the stored barcode(s) to the cradle. \\
 {{ :barcodescan:barcodescan:wasp_wws_750:page224.jpg?400 |}}