wasp_wws750_barcode_scanner
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
wasp_wws750_barcode_scanner [2021/01/28 12:15 (3 years ago)] – swind | wasp_wws750_barcode_scanner [2021/07/15 09:24 (3 years ago)] (current) – swind | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Wasp WWS750 Barcode Scanner ====== | ====== Wasp WWS750 Barcode Scanner ====== | ||
- | [[http:// | + | <note important> |
+ | </note> | ||
{{ : | {{ : | ||
- | ====== Overview ====== | + | ====== Overview |
+ | - Scans Popular 1D and 2D Barcodes | ||
+ | - Data Collect 295ft (90m) from Base | ||
+ | - 30,000+ Continuous Scans on One Full Charge | ||
+ | - Durable 6.6ft (2m) Drop Spec and IP65 Rating | ||
+ | - Green Spot Technology for Good-Read Feedback | ||
====== Details ====== | ====== Details ====== | ||
- | {{ : | + | The full programming manual can be downloaded from this link \\ |
+ | {{ : | ||
+ | Or directly from Wasp's web site. \\ | ||
+ | http:// | ||
+ | |||
+ | ====== STX Prefix ====== | ||
+ | |||
+ | Print the following PDF and follow the instructions on that page. | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | |||
+ | To test that the STX Prefix (Ctrl+B) has been programmed successfully, | ||
+ | You should see something like this: | ||
+ | |||
+ | {{dos1.jpg|}} | ||
+ | |||
+ | What you are looking for is that the scanner scanned a ^B before the barcode and it translates to a little smiley face character on the next line. | ||
+ | If this is what you see, you have correctly programmed the barcode scanner. | ||
+ | |||
+ | \\ | ||
+ | \\ | ||
+ | |||
+ | If you are running Windows 10 and still do not get the ^B character, you will need to run the command prompt as an administrator on the local workstation, | ||
+ | |||
+ | * Click Search or right click on the Windows button on the task bar and select Search. | ||
+ | * Type cmd. Command Prompt should show at the top of the search window. | ||
+ | * Right click on Command Prompt and select run as administrator. | ||
+ | * Right click on the top of the command prompt window where it says Administrator: | ||
+ | * On the bottom of the Command Prompt Properties window, check the checkbox that says Use legacy console (requires relaunch). | ||
+ | * Click OK and then close the command prompt window. | ||
+ | * Relaunch the command prompt and scan a barcode. You should now see the ^B | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ====== Optional Programming ====== | ||
+ | |||
+ | There are a couple options that can be enabled if the scanner appears to be dropping barcodes. From what I have seen, this occurs when the barcode scanner or the cradle loses communication with one-another. \\ | ||
- | ====== Solution ====== | + | Good Read: When to Indicate - Page 68 \\ |
+ | Specifies when the reader will provide an indication (beep and/or flash its green LED), upon successfully reading a barcode. \\ | ||
+ | the default setting is " | ||
- | Good Read: When to Indicate Page 68 \\ | + | If you are experiencing disconnects between |
- | Specifies when the reader will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. \\ | + | |
- | Default is Indicate Good Read = After Decode \\ | + | |
- | Change | + | |
- | {{ : | + | {{ : |
- | Batch Mode Page 208 \\ | + | Batch Mode - Page 208 \\ |
- | This option specifies whether to store labels in the handheld while disconnected from the base. \\ | + | This option specifies whether |
- | Options are as follows: \\ | + | By default batch mode is Disabled. this means the handheld will not store/batch labels. It will send the barcodes one at a time. If communication is lost between the scanner and cradle, the barcode will be lost. \\ |
- | Default | + | \\ |
- | Change | + | A better option would be to change this setting |
- | Jude will change this and test. This would also help eliminate missed scans \\ | + | This would also help eliminate missed scans \\ |
- | {{ : | + | {{ : |
- | Bluetooth Reconnect Attempt Mode Page 224 \\ | + | Bluetooth Reconnect Attempt Mode - Page 224 \\ |
- | Enable/ | + | Enable/ |
+ | This is already | ||
+ | With this enabled, if a barcode is stored in the barcode scanner but it couldn' | ||
{{ : | {{ : | ||
+ | \\ | ||
+ | \\ | ||
Line 43: | Line 98: | ||
== Steve Wind - January 28, 2021 == | == Steve Wind - January 28, 2021 == | ||
+ | == Updated July 14, 2021 == |
wasp_wws750_barcode_scanner.1611864930.txt.gz · Last modified: 2021/01/28 12:15 (3 years ago) by swind